300-120 WLSI — Cisco Certified Specialist - Wireless Advanced Solutions
Test your knowledge with official exam-style questions
Questions and options are shuffled each attempt
Email me this practice set
Get a link sent to your inbox so you can pick this back up anytime.
▶Cisco Certified Specialist - Wireless Advanced Solutions — Practice Set 1: All Questions & Explanations
Full question text, answer options, and explanations for this practice set — a spoiler-free alternative is the interactive quiz above for scored, shuffled practice.
1. A Catalyst 9800 administrator wants a branch AP that currently runs in local mode to operate as a FlexConnect AP. Which site tag configuration converts the AP to FlexConnect mode?
- A. Leave Enable Local Site checked and attach a flex profile to the site tag
- B. Uncheck Enable Local Site in the site tag and select a flex profile, then assign the site tag to the AP(correct)
- C. Enable Central Switching in the policy profile used by the AP
- D. Set the AP join profile to FlexConnect mode
Explanation: B is correct. The 9800 documentation states that any AP that receives a site tag with Enable Local Site disabled (no local-site) is converted into FlexConnect mode, and that an AP in local mode that receives such a site tag reboots and comes back in FlexConnect mode. A is wrong because the Flex Profile option is not even available while Enable Local Site is enabled, and APs given a site tag with Enable Local Site enabled are configured as local mode. C is wrong because central switching is a per-WLAN policy profile setting that controls where client traffic is switched; it does not change the AP mode. D is wrong because on the 9800 the AP mode is derived from the site tag, not from an AP join profile mode setting.
2. A branch SSID is locally switched on FlexConnect APs. The administrator entered the DHCP server address in the Advanced tab of the policy profile, but clients on the SSID do not get addresses. The DHCP server sits in a different VLAN from the client VLAN. What is the correct fix?
- A. Nothing needs to change; the policy profile DHCP server address is relayed by the AP for locally switched WLANs
- B. Allow the client VLAN on the AP switchport and configure an IP helper on the client VLAN SVI or default gateway(correct)
- C. Enable DHCP proxy on the AP so it answers on behalf of the server
- D. Switch the WLAN to central switching and keep the policy profile DHCP setting
Explanation: B is correct. For locally switched WLANs the client DHCP request goes directly into the wired network from the AP interface. The AP has no SVI in the client subnet and therefore cannot perform DHCP proxy, so the DHCP relay setting in the policy profile has no meaning. The switchport must carry the client VLAN and, if the DHCP server is in another VLAN, the IP helper must be configured on the client SVI or default gateway. A is wrong because that setting is ignored for local switching. C is wrong because the AP cannot do DHCP proxy. D changes the design rather than fixing it, and is not what the documentation prescribes for a locally switched WLAN.
3. Where must an ACL be applied so that it restricts clients on a locally switched FlexConnect WLAN on a Catalyst 9800?
- A. Only in the policy profile under Access Policies
- B. Only in the flex profile Policy ACL section
- C. In the policy profile (WLAN ACL) and also in the flex profile Policy ACL section(correct)
- D. On the site tag, because it carries the flex profile reference
Explanation: C is correct. For a locally switched WLAN the traffic is released at the AP, so the ACL defined on the controller must be pushed to the AP. The documented procedure is two steps: apply the ACL in the policy profile (Access Policies, WLAN ACL) and add it to the flex profile Policy ACL section. A is the procedure for a centrally switched WLAN, where traffic is released at the WLC and nothing needs to be pushed to the AP. B omits the policy profile step. D is wrong because the site tag only references the flex profile and does not carry ACLs.
4. Which statement correctly describes efficient image upgrade for FlexConnect APs on the Catalyst 9800?
- A. Every AP downloads the image directly from the controller at the same time to finish quickly
- B. The controller selects one primary AP per AP model per site tag, and up to three secondary APs download from that primary AP at a time(correct)
- C. The controller selects a single primary AP for the entire controller, and all other APs download from it
- D. Secondary APs download from the primary AP over CAPWAP, and the feature works with the default site tag
Explanation: B is correct. The documentation states that the primary AP is one AP per model per site tag, that it downloads the image from the controller over the WAN, and that at most three secondary APs download simultaneously from the primary AP using TFTP. A describes the standard behaviour that the feature is designed to avoid, because it saturates the WAN. C is wrong because selection is per model per site tag, not global. D is wrong on both counts: secondaries use TFTP from the primary, and efficient image upgrade does not operate when the default site tag is applied.
5. Which pairing of Catalyst 9800 precious metal QoS policy and traffic type is correct?
- A. Gold for VoIP clients, Platinum for video clients
- B. Platinum for VoIP clients, Gold for video clients(correct)
- C. Silver for VoIP clients, Bronze for video clients
- D. Bronze for VoIP clients, Silver for background updates
Explanation: B is correct. The precious metal policies are Platinum for VoIP (highest priority), Gold for video (high priority, lower than Platinum), Silver for best-effort traffic, and Bronze for non-real-time or background traffic. The other options swap or misassign tiers. The policies are system defined and cannot be modified or removed by administrators.
6. A branch uses FlexConnect APs and the team enables Application Visibility and Control (AVC). Where does NBAR deep packet inspection run in this deployment, and how does the controller learn the application statistics?
- A. On the controller; the AP forwards raw client traffic only
- B. On the AP; the AP periodically sends FNFv9 reports to the controller(correct)
- C. On Cisco ISE; the controller queries ISE for application data
- D. On the AP in local mode only; FlexConnect does not support AVC
Explanation: B is correct. The documentation states that in FlexConnect (and Fabric) mode NBAR runs on the AP, AVC pushes the FNF configuration to the APs, and the APs regularly send FNFv9 reports to the controller. In local mode NBAR runs on the controller instead, so A describes local mode. C is wrong because ISE is not involved in AVC. D is wrong because FlexConnect mode is explicitly supported for AVC (with restrictions such as no IPv6 classification).
7. A wireless network has APs on subnets different from the controller wireless management interface, and the routed network does not support multicast routing. Which controller multicast delivery method is required?
- A. Multicast mode with a CAPWAP multicast group
- B. Unicast mode, where the controller unicasts every multicast packet to each AP(correct)
- C. IGMP snooping only, with no multicast mode configured
- D. Multicast VLAN groups with APs in sniffer mode
Explanation: B is correct. Unicast mode is inefficient and generates extra traffic, but the documentation says it is required on networks that do not support multicast routing, which includes the case where APs are on different subnets than the wireless management interface. A needs multicast routing in the network. C is wrong because IGMP snooping optimises delivery; it does not replace the multicast or unicast transport to APs. D is wrong because APs in sniffer mode do not join the CAPWAP multicast group.
8. What is the purpose of Directed Multicast Service (DMS) on a Catalyst 9800 WLAN?
- A. It lets any client receive multicast at the lowest basic rate without waking at each DTIM
- B. For 802.11v-capable clients that request it, the AP buffers multicast traffic and sends it as unicast frames when the client wakes, possibly at a higher link rate(correct)
- C. It converts all multicast traffic to broadcast on the management VLAN
- D. It disables IGMP snooping for the WLAN so clients receive all groups
Explanation: B is correct. DMS is enabled on a client request, is supported only on 802.11v-capable clients such as Apple iPad and iPhone, and has the AP buffer multicast and transmit it as unicast when the client wakes. This improves delivery and battery life, because without DMS the client must wake at each DTIM interval. A mis-describes the behaviour. C and D are not functions of DMS.
9. An enterprise needs Apple AirPlay devices on one VLAN discoverable from clients on another. Which TWO statements about Bonjour/mDNS on the Catalyst 9800 are correct?
- A. Bonjour uses UDP port 5353 and sends to 224.0.0.251 (IPv4) or FF02::FB (IPv6)(correct)
- B. The mDNS gateway is enabled by default on the controller
- C. The mDNS gateway caches service advertisements so sources and clients can be in different subnets(correct)
- D. mDNS multicast is forwarded across Layer 3 boundaries by default
- E. The source IP of outgoing mDNS packets is always the AP IP address
Explanation: A and C are correct. The documentation states Bonjour uses mDNS on UDP port 5353 to the link-local addresses 224.0.0.251 and FF02::FB, and that the controller acting as a Bonjour gateway listens for and caches advertisements so that sources and clients can reside in different subnets. B is wrong because the mDNS gateway is disabled by default and must be explicitly enabled. D is wrong because the address is link-local and only forwarded within the local Layer 2 network, which is why the gateway is needed. E is wrong because the source address of outgoing mDNS packets is the mDNS source interface VLAN SVI address, with the wireless management interface as the default.
10. A 9800 controller must register to Cisco Spaces using direct NMSP cloud services. Which TWO prerequisites does the configuration guide list before configuring the server URL and token?
- A. Configure a DNS server so the controller can resolve the FQDNs used by NMSP cloud services(correct)
- B. Import trusted root CA certificates into the crypto PKI trustpool(correct)
- C. Open TCP port 16113 to Cisco Spaces
- D. Configure an SSH username with privilege 15 for Cisco Spaces
- E. Enable the mDNS gateway
Explanation: A and B are correct. The guide says to configure DNS (ip name-server) so the controller can resolve FQDNs used by NMSP cloud services, and to import third-party root CAs into the trustpool (crypto pki trustpool import url) because root CA certificates are not preinstalled and the controller verifies the peer certificate. C is wrong because the NMSP cloud-service uses HTTPS as its transport; TCP 16113 is the NMSP port used with an on-premises CMX. D is the CMX on-premises onboarding method, not Spaces cloud registration. E is unrelated.
11. An engineer adds a Catalyst 9800 to an on-premises CMX. Which pair of TCP ports must be open between the WLC and CMX?
- A. TCP 22 (SSH) and TCP 16113 (NMSP)(correct)
- B. TCP 443 and TCP 8443
- C. TCP 5353 and TCP 5246
- D. TCP 80 and TCP 830
Explanation: A is correct. The configuration example states that port TCP 22 (SSH) and TCP 16113 (NMSP) must be open between the 9800 and CMX: CMX uses SSH to configure the controller and then establishes the NMSP tunnel. The other pairs are not the ports named for this CMX connectivity (5353 is mDNS and 5246 is CAPWAP control, which are unrelated to CMX onboarding).
12. A client is associated and active on the wireless controller, but it does not appear in Cisco Spaces Detect and Locate. Which explanation is consistent with the documentation?
- A. Spaces tracks only active devices that send Wi-Fi probes at intervals of five minutes or less, so a device that rarely probes can be non-locatable(correct)
- B. Spaces tracks only devices that are not associated to any SSID
- C. Detect and Locate requires every client to run a Cisco app
- D. Spaces counts clients exactly as the controller does, so the counts must always match
Explanation: A is correct. The overview says Cisco Spaces tracks only active devices, defined as those sending a Wi-Fi probe packet at intervals of five minutes or less, and that devices considered active by the controller but not probing are non-locatable. B is wrong because associated clients are displayed. C is invented. D is wrong because the documentation explicitly says client counts cannot be directly compared between Spaces and the controller.
13. Two Cisco Spaces Connector 3 instances are deployed as a VIP-paired high availability pair with a firewall between them. Failover does not work. Which firewall configuration is required?
- A. Permit VRRP (IP protocol 112) between the connectors and HTTPS TCP 443 in both directions, with both connectors in the same Layer 2 segment(correct)
- B. Permit only UDP 5353 between the connectors
- C. Permit TCP 16113 between the connectors
- D. Permit ICMP only, because HA uses ping to detect the peer
Explanation: A is correct. Connector HA uses VRRP to determine instance state, so IP protocol 112 must be allowed (source and destination matching the connector physical IPs) and the connectors must reside in the same Layer 2 or VLAN segment. HA also uses HTTPS to assess the status of its peer, so TCP 443 must be permitted in both directions. B, C and D name protocols that are not used for connector peer health checks.
14. Which description of Central Web Authentication (CWA) on the Catalyst 9800 is correct?
- A. It is Layer 3 security where the controller hosts the login page and authenticates credentials locally
- B. It is typically Layer 2 security, where ISE pushes the redirect URL and ACL name through RADIUS and hosts the portal(correct)
- C. It is Layer 3 security where an external server hosts the page and the pre-auth ACL is static on the controller
- D. It is an 802.1X EAP method that needs no web page
Explanation: B is correct. CWA is typically configured as Layer 2 security (often MAC filtering) with the redirection URL and pre-authentication ACL residing on Cisco ISE, which sends redirection attributes to the controller during Layer 2 authentication. A describes local web authentication (LWA). C describes external web authentication (EWA). D is wrong because CWA is a web-based method.
15. A CWA WLAN is configured with MAC filtering and ISE returns a redirect URL and ACL name, but clients are never redirected. The policy profile has neither AAA override nor NAC enabled. What must be enabled?
- A. Central association and central DHCP
- B. Both AAA override and NAC state in the policy profile(correct)
- C. Only the Layer 3 web auth parameter map
- D. Only 802.11r Fast Transition
Explanation: B is correct. The CWA configuration guide states that both NAC and AAA override must be configured in the policy profile: AAA override applies the policies returned by ISE, and NAC is used to trigger central web authentication when a redirect URL and ACL are received. The other settings are unrelated to applying the ISE-returned redirect.
16. In a CWA redirect ACL on the 9800, what does a deny entry mean?
- A. The matching traffic is dropped
- B. The matching traffic is not redirected and stays on the data plane(correct)
- C. The matching traffic is redirected to ISE
- D. The matching traffic bypasses authentication permanently
Explanation: B is correct. The redirect ACL is a punt ACL, not a security ACL: traffic matching deny statements passes through the data plane (no redirection, not necessarily dropped), and traffic matching permit statements is sent to the control plane for web interception and redirection. Therefore A and C reverse or distort the semantics, and D is wrong because a deny in this ACL only skips redirection; it does not grant permanent access.
17. Which statement describes a dual-SSID BYOD design with Cisco ISE?
- A. Users connect to an onboarding SSID, are redirected to the BYOD portal for registration and provisioning, then connect to the secure corporate SSID(correct)
- B. Users onboard on the corporate 802.1X SSID and the open SSID is never used
- C. Two SSIDs are used so that one carries voice and the other data
- D. Users onboard through a controller-hosted local web page with no ISE involvement
Explanation: A is correct. In dual-SSID BYOD, one SSID (open or restricted) is used for onboarding where ISE handles registration, provisioning and policy, and the user then switches to the secure corporate SSID. In single-SSID BYOD, onboarding occurs on the same SSID. B describes single SSID. C and D are not BYOD designs.
18. What does the 9800 documentation say about profiling clients using only the MAC address OUI?
- A. It can identify the manufacturer but cannot differentiate a laptop from a smartphone(correct)
- B. It identifies the exact device model and operating system
- C. It is the only method that works with randomized MAC addresses
- D. It requires Cisco ISE to be in the data path
Explanation: A is correct. The 9800 can perform three types of profiling: MAC OUI, DHCP and HTTP. OUI profiling alone is described as extremely limited: it can classify a device as a specific brand but cannot differentiate a laptop from a smartphone. B is wrong for that reason. C is not supported by the documentation, which lists randomized (locally administered) MAC addresses as a profiling problem. D is wrong because the OUI lookup is done by the WLC.
19. On a Catalyst 9800 with no rogue classification rules enabled, how are newly detected unknown access points categorized?
- A. Malicious
- B. Friendly - External
- C. Unclassified(correct)
- D. Contained
Explanation: C is correct. By default no classification rules are active, so all unknown access points are assigned the Unclassified state until administrators enable rules. A rogue found on the same wired network is the exception and is marked Threat and classified Malicious automatically. Friendly classification comes from the friendly MAC list, a matching rule, or manual assignment, and Contained is an action state, not a default.
20. Catalyst Center detects an AP that is not managed by Catalyst Center and advertises the same SSID as the corporate network. How does the Rogue Management application classify it?
- A. Neighbor
- B. Honeypot(correct)
- C. Rogue on wire
- D. Interferer
Explanation: B is correct. Per the Catalyst Center Rogue Management documentation, an AP unknown to Catalyst Center that uses the same SSID as your network is classified as Honeypot. Rogue on wire applies to an AP not using the network SSID that is connected to the corporate wired network (requires Cisco switches managed by Catalyst Center). Interferer and Neighbor apply to APs not using the same SSID and not on the wire, distinguished by signal threshold of -75 dBm.
21. According to the Cisco CleanAir documentation, how is the Air Quality Index (AQI) interpreted?
- A. An AQI of 100 is poor and zero is good
- B. An AQI of zero is poor and greater than 85 is good(correct)
- C. An AQI between 40 and 60 is good
- D. AQI measures client count per radio
Explanation: B is correct. The CleanAir terms table states an AQI of zero is considered poor and an AQI greater than eighty-five is considered good. AQI indicates air quality based on RF interference, so A inverts the scale, C gives an unsupported range and D is wrong.
22. In Catalyst Center Assurance, the Connectivity RSSI dashlet reports the percentage of client RSSI measurements better than which threshold?
- A. -90 dBm
- B. -72 dBm(correct)
- C. -60 dBm
- D. -50 dBm
Explanation: B is correct. The Assurance client health documentation states that the Connectivity RSSI dashlet provides the percentage of RSSI measurements for all clients whose RSSI is higher than the threshold of -72 dBm. The companion SNR dashlet uses a threshold of 10 dB.
23. Which external authentication methods can a Catalyst 9800 use for administrator (GUI/CLI) logins?
- A. RADIUS and TACACS+ only(correct)
- B. RADIUS, TACACS+ and LDAP
- C. LDAP and Kerberos
- D. TACACS+ only
Explanation: A is correct. The documentation states that RADIUS and TACACS+ are the only two external authentication methods for admin users, and explicitly notes there is no LDAP for admin login. Therefore B, C and D are wrong.
24. A help-desk user authenticates to the 9800 WebUI through TACACS+ and is returned privilege level 5. What access does the user get?
- A. No GUI access
- B. Full read-write access
- C. Access to the Monitor tab only(correct)
- D. Access to the Configuration tab only
Explanation: C is correct. For WebUI authentication via RADIUS or TACACS+, privilege levels 1 through 14 can only view the Monitor tab (equivalent to a read-only local user). Privilege 0 has no GUI access, and privilege 15 has full access. B and D are therefore incorrect.
25. A team wants to configure APs as 802.1X supplicants and wants the EAP type that needs only a username and password with no certificates on the AP. Which should they choose?
- A. EAP-TLS
- B. PEAP
- C. EAP-FAST(correct)
- D. EAP-TLS with LSC
Explanation: C is correct. In the AP join profile the EAP type can be EAP-FAST, EAP-TLS or EAP-PEAP. The document states EAP-FAST is the only type that uses username and password only and is the easiest to set up, whereas PEAP and EAP-TLS require certificates provisioned to the APs through the LSC workflow.