300-420 ENSLD — Cisco Certified Specialist - Enterprise Design
Test your knowledge with official exam-style questions
Questions and options are shuffled each attempt
Email me this practice set
Get a link sent to your inbox so you can pick this back up anytime.
▶Cisco Certified Specialist - Enterprise Design — Practice Set 1: All Questions & Explanations
Full question text, answer options, and explanations for this practice set — a spoiler-free alternative is the interactive quiz above for scored, shuffled practice.
1. An enterprise is writing a structured IPv4 addressing plan for internal networks that will never be routed on the public Internet. Which block is one of the address ranges reserved for private use by RFC 1918?
- A. 172.16.0.0/12(correct)
- B. 172.0.0.0/8
- C. 192.0.0.0/8
- D. 11.0.0.0/8
Explanation: RFC 1918 reserves exactly three blocks for private internets: 10.0.0.0/8, 172.16.0.0/12 (172.16.0.0 - 172.31.255.255) and 192.168.0.0/16. The 172.16.0.0/12 block is the second of these. 172.0.0.0/8 is far larger than the reserved 172.16.0.0/12 and mostly consists of publicly routable space, 192.0.0.0/8 is not a private block (only 192.168.0.0/16 is), and 11.0.0.0/8 is not among the three reserved ranges.
2. A company plans an IPv6 addressing scheme for internal data-centre networks. Requirements: prefixes must be globally unique with high probability so that sites can later be merged without renumbering, they must not depend on any ISP, and they should be identifiable by a well-known prefix so they are easy to filter at site boundaries. Which address type meets these requirements?
- A. Link-local addresses in FE80::/10
- B. Unique Local IPv6 unicast addresses in FC00::/7(correct)
- C. Multicast addresses in FF00::/8
- D. The loopback address ::1/128
Explanation: RFC 4193 defines Unique Local IPv6 Unicast Addresses in the well-known prefix FC00::/7. They use a pseudo-randomly generated 40-bit Global ID (globally unique with high probability), are ISP independent, allow sites to be combined without address conflicts or renumbering, and the well-known prefix makes filtering at site boundaries easy. Link-local addresses (FE80::/10) are only valid on a single link and are never forwarded by routers, multicast (FF00::/8) is not a unicast addressing scheme for subnets, and ::1/128 is the loopback address of a single node.
3. In an IS-IS design with multiple areas, an IP-capable Level 1 router receives a packet whose destination does not match any IP reachability learned within its own area. What does the router do with the packet?
- A. It forwards the packet toward the nearest Level 2 router(correct)
- B. It discards the packet because Level 1 routers have no route toward other areas
- C. It forwards the packet to the neighbor with the highest system ID
- D. It floods the packet to all Level 1 neighbors in the area
Explanation: RFC 1195 states that IP-capable Level 1 routers maintain the topology and destinations only within their own area. If a destination does not match any [address, mask, metric] reachable in the area, the packet is routed toward the nearest Level 2 router. Discarding would break inter-area connectivity, packets are not flooded, and system ID ordering plays no role in this forwarding decision.
4. A router running EIGRP has three paths to 10.9.0.0/16. Via neighbor N1 the total metric is 3,000,000 and N1 reports a distance of 1,500,000. Via N2 the total metric is 4,200,000 and N2 reports 2,800,000. Via N3 the total metric is 3,900,000 and N3 reports 3,000,000. N1 is the successor. Which neighbors are feasible successors?
- A. Both N2 and N3
- B. Neither N2 nor N3
- C. N3 only
- D. N2 only(correct)
Explanation: The feasible distance (FD) is the best metric, 3,000,000 via N1. Under the Feasibility Condition (RFC 7868) a neighbor is a feasible successor only if its reported distance is less than the FD. N2 reports 2,800,000 which is less than 3,000,000, so it qualifies. N3 reports exactly 3,000,000, which is equal to - not less than - the FD, so it fails the condition even though its total metric is better than N2's. Therefore only N2 is a feasible successor.
5. A remote OSPF area has a single area border router as its only exit and its internal routers have limited memory. The design goal is to shrink the link-state database in that area while still giving internal routers reachability to external destinations. What should the designer do?
- A. Change all external routes to OSPF Type 2 metrics
- B. Configure the area as a stub area so the ABR advertises a default route into it(correct)
- C. Add a virtual link from the area to area 0 to suppress external routes
- D. Merge the area into the backbone (area 0)
Explanation: RFC 2328 describes stub areas for exactly this case: AS-external-LSAs are not flooded into the stub area, which reduces database size and memory, and the ABR advertises a default route into the area via summary-LSAs so external destinations remain reachable. A stub area is appropriate when there is a single exit point. Merging the area into the backbone would flood more, not less, information; a virtual link maintains backbone connectivity and does not suppress external LSAs; and changing the external metric type only changes how costs are compared, not whether the LSAs are flooded.
6. An enterprise AS has two Internet edge routers connected to ISP-A and ISP-B. Policy: all routers in the AS must prefer ISP-A for outbound traffic. Which action on routes received from ISP-A best achieves this?
- A. Prepend the AS number to the routes advertised toward ISP-B
- B. Set a higher LOCAL_PREF so it is carried to all iBGP peers(correct)
- C. Set a lower MED on the routes
- D. Set a higher WEIGHT on the edge router
Explanation: LOCAL_PREF is a well-known attribute included in updates sent to internal peers, and the higher value is preferred (RFC 4271); it is evaluated early in the BGP best-path process, so setting a higher value on ISP-A routes steers every router in the AS toward ISP-A. WEIGHT is Cisco-specific and local to the router where it is configured, so it is not shared with other iBGP routers. MED is only compared between paths from the same neighboring AS by default and is meant to influence how a neighbor enters your AS. AS_PATH prepending toward ISP-B influences inbound traffic, not outbound path selection.
7. According to Cisco campus design guidance, which is a benefit of a Layer 3 routed access design?
- A. VLANs can be extended across many access closets without restriction
- B. Spanning tree blocked links are eliminated so both uplinks can carry traffic(correct)
- C. No routing protocol is required between access and distribution layers
- D. The distribution layer must run an FHRP for every access VLAN
Explanation: In a Layer 3 routed access design the access switch becomes the IP gateway, which eliminates spanning-tree loops and blocked links, so both uplinks can be used and effective bandwidth increases; convergence is also good with minimal tuning. The trade-off is that Layer 2 domains are confined to a single access closet, so the claim that VLANs can be extended across many closets is the opposite of reality. Routed access obviously needs a routing protocol, and because the gateway is at the access layer the distribution FHRP is no longer needed for those VLANs.
8. Which first-hop redundancy protocol provides greater uplink utilization by balancing load from hosts across multiple uplinks, but can only be used in a non-looped topology?
- A. GLBP(correct)
- B. HSRP
- C. VRRP
- D. Nonstop Forwarding (NSF)
Explanation: The Cisco campus design guide notes that HSRP and VRRP only allow hosts to send traffic out one of the access uplinks, whereas GLBP balances load from hosts across multiple uplinks but can only be used in a non-looped topology. NSF is not an FHRP; it is a graceful-restart capability that lets an SSO-enabled device keep forwarding while routing adjacencies are re-established.
9. In a VRRPv3 (RFC 5798) deployment, Rtr1 owns the IP address that is used as the virtual router address and Rtr2 is a backup using the default priority. Which priorities do the two routers use?
- A. Rtr1 uses 255; Rtr2 uses 100(correct)
- B. Rtr1 uses 254; Rtr2 uses 1
- C. Rtr1 uses 0; Rtr2 uses 100
- D. Rtr1 uses 100; Rtr2 uses 255
Explanation: RFC 5798 states that the VRRP router that owns the virtual router IP address MUST use priority 255, while backup routers use values 1-254 with a default of 100. Priority 0 has a special meaning - the current master has stopped participating in VRRP, which triggers backups to take over quickly - so it is not a normal operating priority for an address owner. Priority 255 is reserved for the address owner, so a backup cannot use it.
10. Access ports for end users have PortFast enabled. A user connects a small switch that sends BPDUs claiming a very low bridge priority. The design requirement is that the port must be shut down immediately when a BPDU is received. Which feature meets the requirement?
- A. Root guard, which places the port in the root-inconsistent state
- B. Enabling RSTP on the uplinks
- C. Loop guard
- D. BPDU guard, which places the port in the errdisable state(correct)
Explanation: BPDU guard complements PortFast: when a BPDU is received on a PortFast-enabled port, the switch immediately places the port in the errdisable state, and it does not recover on its own unless errdisable recovery is configured. Root guard instead moves the port to a root-inconsistent (listening-equivalent) state and recovers automatically as soon as superior BPDUs stop; it allows the device to keep participating in STP. Loop guard protects non-designated ports against loss of BPDUs (unidirectional links) and is unrelated to this scenario. RSTP on the uplinks does not stop a rogue switch on an access port.
11. Which statement correctly maps the four operational planes of Cisco SD-Access to the technology that implements each plane?
- A. Control plane: OMP; data plane: IPsec; policy plane: Catalyst Center; management plane: LISP
- B. Control plane: BGP; data plane: MPLS; policy plane: ACLs; management plane: SNMP
- C. Control plane: VXLAN; data plane: LISP; policy plane: Cisco TrustSec; management plane: Catalyst Center
- D. Control plane: LISP; data plane: VXLAN; policy plane: Cisco TrustSec; management plane: Catalyst Center(correct)
Explanation: The SD-Access design guide states that the management plane is enabled by Cisco Catalyst Center, the overlay control plane is based on LISP, the data plane is based on VXLAN, and the policy plane is based on Cisco TrustSec. The first choice swaps LISP and VXLAN. The BGP/MPLS and OMP/IPsec mappings describe other architectures (OMP and IPsec belong to Catalyst SD-WAN) and do not match SD-Access.
12. Select TWO requirements that apply to intermediate nodes in an SD-Access fabric site (the devices between border and edge nodes that are not in a fabric role).
- A. They provide IP reachability and physical connectivity between fabric nodes(correct)
- B. They must be aware of Security Group Tags (SGTs)
- C. They run LISP control plane messaging with the control plane node
- D. They support the additional MTU needed for VXLAN-encapsulated packets(correct)
- E. They perform VXLAN encapsulation and de-encapsulation of fabric traffic
Explanation: The SD-Access design guide states that intermediate nodes have no requirement for VXLAN encapsulation/de-encapsulation, LISP control plane messaging support, or SGT awareness. Their requirement is to provide IP reachability and physical connectivity and to support the additional MTU needed for fabric-encapsulated packets; they simply route and transport IP traffic between fabric nodes. VXLAN encapsulation, LISP control plane messaging and SGT awareness are functions of edge and border nodes (and the control plane node for LISP) rather than intermediate nodes.
13. In the Cisco Catalyst SD-WAN architecture, which component provides the centralized control plane and distributes routes and policy using OMP?
- A. SD-WAN Manager
- B. SD-WAN Validator
- C. SD-WAN Controller(correct)
- D. WAN Edge router
Explanation: The SD-WAN Controller is responsible for the centralized control plane: it maintains secure connections to each WAN Edge router and distributes routes and policy information via the Overlay Management Protocol (OMP), acting as a route reflector. The SD-WAN Manager is the management plane, the SD-WAN Validator is the orchestration plane (initial authentication and NAT traversal facilitation), and the WAN Edge router is the data plane.
14. In Cisco Catalyst SD-WAN, a TLOC is the attachment point where a WAN Edge router connects to a WAN transport. Which three values make up the TLOC identifier?
- A. System IP address, color, and encapsulation(correct)
- B. Public IP address, private IP address, and port
- C. Router ID, area ID, and AS number
- D. Site ID, VPN number, and interface name
Explanation: The SD-WAN design guide states that a TLOC is uniquely identified by a three-tuple of system IP address, color, and encapsulation (GRE or IPsec). The public and private IP addresses and ports are attributes advertised along with the TLOC route, not the identifier itself. Site ID, VPN number, interface name, router ID, area ID and AS number are not part of the TLOC three-tuple.
15. A retailer wants branch routers to build direct, on-demand spoke-to-spoke IPsec tunnels over the Internet without configuring a tunnel between every pair of branches. The hub should act as a registration and resolution server for the spokes. Which technology and mechanism fit?
- A. Point-to-point GRE tunnels from each spoke to every other spoke
- B. DMVPN using mGRE and NHRP(correct)
- C. MPLS Layer 3 VPN using route targets
- D. GET VPN with a key server distributing group keys
Explanation: DMVPN combines multipoint GRE (mGRE), IPsec and the Next Hop Resolution Protocol (NHRP). The hub acts as the NHRP server and the spokes are clients that register their real addresses; when a spoke needs to reach another spoke it queries the NHRP server for the target spoke's real address and builds a dynamic spoke-to-spoke IPsec tunnel on demand. GET VPN is tunnel-less and intended for private WANs, static point-to-point GRE requires per-pair configuration, and MPLS L3 VPN is a provider-delivered service rather than an Internet overlay.
16. An enterprise connects 80 sites over a private MPLS WAN and must encrypt traffic any-to-any without building an overlay of tunnels so that native routing, QoS and multicast behaviour are preserved. A centralized system should distribute keys to trusted members. Which solution fits best?
- A. DMVPN with hub-and-spoke mGRE tunnels
- B. Catalyst SD-WAN with IPsec overlay tunnels
- C. GET VPN with a key server and group members(correct)
- D. Point-to-point IPsec tunnels with GRE between each pair of sites
Explanation: Cisco describes GET VPN as a tunnel-less VPN that eliminates the need for point-to-point tunnels, using trusted group members that register with a key server (GDOI) to obtain IPsec SAs and keys. It preserves network intelligence such as routing, QoS and multicast, can be used in IP and MPLS WANs, and scales for any-to-any connectivity. DMVPN, point-to-point GRE/IPsec and SD-WAN all rely on building tunnels, which is exactly what the requirement avoids.
17. In an MPLS Layer 3 VPN service built per RFC 4364, which devices must hold per-VPN routing information?
- A. All routers, because VPN routes are redistributed into the provider IGP
- B. Only the CE devices of each customer
- C. Every P router in the provider backbone
- D. Only the PE routers that attach to the VPN's sites(correct)
Explanation: RFC 4364 explains that routing information about a particular VPN only needs to be present in the PE routers that attach to that VPN; the P routers do not need to have any per-VPN routing information whatsoever. This is what makes the model scalable. CE devices are logically part of the customer VPN but the provider's PE routers hold the VRFs, and VPN routes are carried between PEs using BGP, not redistributed into every provider router.
18. Which DiffServ per-hop behavior and recommended codepoint is intended as a building block for low-loss, low-delay, low-jitter services such as voice bearer traffic?
- A. Default PHB (000000)
- B. AF11 (001010)
- C. EF (101110)(correct)
- D. AF43 (100110)
Explanation: RFC 3246 defines the Expedited Forwarding (EF) PHB as a building block for low-loss, low-delay and low-jitter services and recommends codepoint 101110. AF11 and AF43 belong to the Assured Forwarding groups (RFC 2597), which provide drop-precedence-based forwarding assurance rather than low-delay treatment, and the default PHB (000000) is best-effort.
19. A service provider contract limits a branch to 50 Mbps. The WAN router should bring the outbound stream into conformance with this profile by delaying excess packets in a buffer rather than discarding them immediately. Which mechanism does this?
- A. Policing
- B. Shaping(correct)
- C. Classification
- D. Marking
Explanation: RFC 2475 defines shaping as the process of delaying packets within a traffic stream to cause it to conform to a defined traffic profile; shapers use a finite buffer, and packets may be discarded only if the buffer is exhausted. Policing, in contrast, is the process of discarding packets in accordance with the state of a meter enforcing the profile. Classification selects the traffic and marking sets the codepoint; neither enforces a rate.
20. In PIM Sparse Mode (RFC 4601), a receiver announces interest in group G using IGMP. Toward which device does the receiver's designated router send the resulting (*,G) Join?
- A. The IGMP querier on the source LAN
- B. The multicast source
- C. The rendezvous point for group G(correct)
- D. The MSDP peer of the local RP
Explanation: In PIM-SM phase one, the receiver's DR sends a (*,G) Join hop by hop toward the rendezvous point (RP) for the group, instantiating shared-tree (RP tree) state along the path. The (S,G) Join toward a source only happens later when a source-specific tree is built. The IGMP querier and MSDP peers are not the target of the (*,G) Join.
21. A media company distributes a live video feed from one known source to many receivers and wants to avoid rendezvous points and shared trees entirely. Which multicast service model and IPv4 address range are designated for this use?
- A. Source-specific multicast (SSM) with 232.0.0.0/8(correct)
- B. MSDP with 232.0.0.0/8
- C. PIM bidirectional with 224.0.0.0/24
- D. Any-source multicast with 239.0.0.0/8 and an RP
Explanation: RFC 4607 designates IPv4 232/8 (232.0.0.0 - 232.255.255.255) for source-specific multicast. An SSM channel is identified by (S,G), SSM provides one-to-many delivery, and it avoids the shared trees and rendezvous points required by PIM-SM ASM. Bidirectional PIM and ASM still depend on an RP, and MSDP is a mechanism to connect PIM-SM domains, not a service model.
22. Why does the DiffServ architecture scale better in large networks than per-flow reservation approaches?
- A. Every router must reclassify each packet using deep inspection
- B. Every application must mark packets with a unique codepoint per flow
- C. Complex classification and conditioning is done at boundary nodes, and core nodes apply per-hop behaviors to aggregates(correct)
- D. Core routers keep per-flow state and signal reservations with RSVP
Explanation: RFC 2475 states that DiffServ achieves scalability by implementing complex classification and conditioning functions only at network boundary nodes and applying per-hop behaviors to aggregates of traffic that were marked using the DS field, so per-application-flow or per-customer forwarding state need not be maintained in the core. Per-flow state and RSVP signalling is the IntServ model that DiffServ avoids, and per-packet deep inspection at every router or per-flow codepoints would not scale.
23. What is the purpose of the YANG language in network automation?
- A. It is an HTTP-based API for retrieving device data
- B. It is a transport protocol that carries configuration over SSH
- C. It is a data modeling language for configuration data, state data, RPCs and notifications(correct)
- D. It is a streaming protocol that sends telemetry over HTTP/2
Explanation: RFC 7950 describes YANG as a data modeling language used to model configuration data, state data, Remote Procedure Calls and notifications for network management protocols such as NETCONF. Protocols such as NETCONF (RPC over a secure transport) and RESTCONF (HTTP-based) use YANG models; YANG itself is not a transport or streaming protocol.
24. A team wants to automate changes and needs explicit datastore locking so that no other session can change configuration during a maintenance window. Which protocol should they choose, and why?
- A. NETCONF, because it supports datastores and explicit locking while RESTCONF does not(correct)
- B. Either protocol, because RESTCONF mirrors the full NETCONF functionality
- C. RESTCONF, because it uses candidate datastores with confirmed commit
- D. RESTCONF, because it exposes lock and unlock operations over HTTP
Explanation: RFC 8040 explains that RESTCONF implements only a subset of NETCONF's interaction capabilities - for instance by eliminating datastores and explicit locking - and that RESTCONF cannot manipulate locks. NETCONF defines the <lock> and <unlock> operations (and candidate/confirmed-commit capabilities), so it is the right choice when explicit locking is required. The answers that credit RESTCONF with lock operations, candidate/confirmed-commit control, or full NETCONF parity are incorrect.
25. A Cisco IOS XE switch pair performs a stateful switchover. The operations team requires that telemetry to the collector resumes automatically without the collector having to re-establish anything. Which subscription type satisfies this?
- A. Either type, because both survive stateful switchover
- B. Neither type, because telemetry always stops during a switchover
- C. A dynamic (dial-in) subscription created by the collector
- D. A configured (dial-out) subscription defined in the device configuration(correct)
Explanation: The Cisco model-driven telemetry documentation explains that dynamic (dial-in) subscriptions are tied to the session that created them and must be reinitiated after a reload because established sessions are killed during stateful switchover. Configured (dial-out) subscriptions are part of the running configuration and automatically reconnect to the receiver after a stateful switchover. Therefore a configured dial-out subscription is the correct choice.