300-410 ENARSI — Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation
Test your knowledge with official exam-style questions
Questions and options are shuffled each attempt
Email me this practice set
Get a link sent to your inbox so you can pick this back up anytime.
▶Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation — Practice Set 1: All Questions & Explanations
Full question text, answer options, and explanations for this practice set — a spoiler-free alternative is the interactive quiz above for scored, shuffled practice.
1. A branch router learns the prefix 172.16.40.0/24 from three sources: OSPF, internal EIGRP and RIP. All three are running with default administrative distances. Which route does the router install in its routing table?
- A. The OSPF route, because OSPF has the highest administrative distance of the three
- B. The internal EIGRP route, because its default administrative distance of 90 is the lowest of the three(correct)
- C. The RIP route, because RIP has the highest default administrative distance of the three
- D. All three routes, because the router load-shares across routing protocols by default
Explanation: The correct answer is B. Cisco lists the default administrative distances as internal EIGRP 90, OSPF 110 and RIP 120, and the route with the lowest administrative distance is preferred and installed. Administrative distance only matters when several sources advertise the same prefix, which is exactly this case. Option A and option C are wrong because a higher administrative distance is less trusted, not more. Option D is wrong because only the most believable source is installed; administrative distance is used to choose between protocols, not to load-share across them.
2. A router reaches 10.50.0.0/16 through OSPF (default administrative distance). An engineer adds a static route to the same prefix through a backup ISP link. The static route must be used only if the OSPF route disappears. Which administrative distance should be configured on the static route?
- A. 1, the default for a static route
- B. 5, so that the static route is still preferred but only slightly
- C. 100, because it is lower than the default OSPF value(correct)
- D. 130, because it is higher than the OSPF default of 110
Explanation: The correct answer is D. A floating static route uses an administrative distance higher than that of the primary route, so it stays out of the routing table until the primary route is removed. OSPF defaults to 110, so 130 works. Options A and B are lower than 110, so the static route would win and the OSPF route would never be used. Option C (100) is also lower than 110, so the static route would still be preferred while OSPF is healthy.
3. Router R5 learns 192.168.77.0/24 from an OSPF neighbor and also receives the same prefix in an EIGRP update. The EIGRP route is an external route created by redistribution on another router (`show ip route` would show distance 170 for it). All default distances are in use. Which statement is correct?
- A. R5 installs the OSPF route because OSPF (110) has a lower administrative distance than external EIGRP (170)(correct)
- B. R5 installs the EIGRP route because EIGRP is always preferred over OSPF
- C. R5 installs both routes and load-shares because both come from IGPs
- D. R5 installs the EIGRP route because redistributed routes always have the lowest administrative distance
Explanation: The correct answer is A. Redistribution output on Cisco shows an EIGRP-learned external route with distance 170, while OSPF defaults to 110. The lower value wins, so the OSPF route is installed. Option B is wrong because internal EIGRP (90) beats OSPF but external EIGRP (170) does not. Option C is wrong because administrative distance selects one source; it does not combine different protocols. Option D is wrong because redistributed routes are not given special preference; external EIGRP routes carry a higher distance than internal ones.
4. Which TWO statements about policy-based routing (PBR) on a Cisco router are correct?
- A. `ip policy route-map` on an interface applies PBR to packets arriving on that interface(correct)
- B. `ip local policy route-map` is needed for packets that the router itself generates to be policy routed(correct)
- C. Packets generated by the router are policy routed by default, without any extra command
- D. `ip policy route-map` only affects packets leaving the interface where it is configured
- E. A route-map clause with no match statement matches no packets
Explanation: The correct answers are A and B. Cisco states that a packet arriving on the interface with `ip policy route-map` is subject to policy-based routing, and that packets generated by the device are not normally policy routed unless `ip local policy route-map` is configured. Option C is wrong for exactly that reason. Option D is wrong because PBR is applied to arriving (inbound) packets. Option E is wrong because Cisco states that no match clause in the route map indicates all packets.
5. BFD is enabled on a link between two routers that run OSPF, and OSPF has registered with BFD for the neighbor. The forwarding path between the routers fails, but the interfaces stay up. What is the role of each protocol in the recovery?
- A. BFD removes the failed route from the routing table and installs a backup path itself
- B. BFD sends OSPF hello packets faster so that OSPF discovers the failure on its own
- C. OSPF detects the failure first, and BFD is only used to log the event
- D. BFD detects the forwarding-path failure and the registered routing protocol (OSPF) must then act to bypass the failed neighbor(correct)
Explanation: The correct answer is D. Cisco describes routing protocols as BFD clients that register for each neighbor, and notes that BFD detects a failure but the routing protocol must take action to bypass the failed peer. Option A is wrong because BFD does not manipulate the routing table. Option B is wrong because BFD runs its own control packets and does not change the routing protocol hellos. Option C reverses the roles; the purpose of BFD is detection faster than routing protocol hello mechanisms.
6. A remote-office router is configured with `eigrp stub` and no additional keywords. Which routes does it advertise to its EIGRP neighbors?
- A. Static and redistributed routes only
- B. No routes, because it only receives
- C. Connected and summary routes(correct)
- D. All routes in its topology table
Explanation: The correct answer is C. Cisco states that a stub device shares connected and summary routing information with all neighbors by default. Option A is wrong because static and redistributed routes are advertised only if the static or redistributed keywords are added. Option B describes the `receive-only` keyword, not the default. Option D is wrong because a stub does not advertise everything in its topology table.
7. For a destination, the EIGRP successor on Router E has a metric (feasible distance) of 20. Neighbor X offers a total metric of 35 with a reported distance of 15. Neighbor Y offers a total metric of 38 with a reported distance of 25. The engineer configures `variance 2`. Which paths will Router E use to forward traffic to the destination?
- A. Only the successor, because variance 2 requires a metric of 20 or lower
- B. The successor and the path through Neighbor X only(correct)
- C. The successor and the path through Neighbor Y only
- D. The successor and both paths, because 35 and 38 are both below 40
Explanation: The correct answer is B. With variance 2 the threshold is 2 x 20 = 40, and Cisco notes that a path is used only if it also satisfies the feasibility condition (it must be a feasible successor). Neighbor X has a reported distance of 15, which is less than the feasible distance of 20, and a metric of 35, which is under 40, so it is used. Neighbor Y has a reported distance of 25, which is not less than 20, so it is not a feasible successor and is not used even though 38 is below 40. Option A is wrong because variance multiplies the best metric. Options C and D are wrong because they include Neighbor Y.
8. Area 3 attaches to the OSPF domain only through Area 2. Router R3 is the ABR between Area 3 and Area 2, and Router R2 is the ABR between Area 2 and the backbone. An engineer fixes the missing backbone connection for Area 3 with a virtual link. Which design is correct?
- A. A virtual link between R3 and R2, with Area 2 as the transit area, provided Area 2 is not a stub area(correct)
- B. A virtual link between R3 and R2, with Area 3 as the transit area
- C. A virtual link between any two routers in Area 2, with Area 0 as the transit area
- D. A virtual link between R3 and R2 through Area 2, which works even if Area 2 is configured as a stub area
Explanation: The correct answer is A. Cisco states that the two endpoints of a virtual link are ABRs, that the link runs through the nonbackbone area the two routers have in common (the transit area), and that virtual links cannot be configured through stub areas. R2 and R3 are ABRs that share Area 2. Option B is wrong because Area 3 is not shared by both routers. Option C is wrong because the endpoints must be ABRs and the backbone is not the transit area. Option D is wrong because a stub area cannot be a transit area for a virtual link.
9. A BGP router receives two paths to the same prefix. Path 1 is learned from an iBGP peer with LOCAL_PREF 200 and an AS_PATH length of 3. Path 2 is learned from an eBGP peer with LOCAL_PREF 100 and an AS_PATH length of 1. Weight is not configured for either path. Which path is selected as best?
- A. Path 2, because it has the shorter AS_PATH
- B. Path 1, because the higher LOCAL_PREF is evaluated before AS_PATH length(correct)
- C. Path 2, because eBGP paths always win over iBGP paths
- D. Neither; the router selects the path from the lowest neighbor address
Explanation: The correct answer is B. In Cisco's best-path order, the highest weight is checked first, then the highest LOCAL_PREF, and only later the shortest AS_PATH, the lowest MED, and eBGP over iBGP. Weight is equal, so LOCAL_PREF 200 decides the result. Option A is wrong because AS_PATH length is evaluated after LOCAL_PREF. Option C is wrong because the eBGP over iBGP rule is applied much later in the algorithm. Option D is wrong because the lowest neighbor address is the very last tiebreaker.
10. In a service provider MPLS Layer 3 VPN, which devices must maintain customer VPN routes in per-customer VRF routing tables?
- A. Provider (P) routers in the core only
- B. Both P routers and PE routers
- C. Provider edge (PE) routers that connect to customer sites(correct)
- D. Only the customer edge (CE) routers of the provider
Explanation: The correct answer is C. Cisco states that P devices do not maintain any VPN routes; PE devices hold the per-VRF routing and forwarding tables for the VPNs they serve. Options A and B are wrong because P routers only label-switch. Option D is wrong because the question concerns the provider network, and the CE routers belong to the customer side of the attachment.
11. Two customers on the same PE router both use the prefix 10.1.0.0/16. Which element lets MP-BGP carry both prefixes as distinct VPN routes?
- A. The route target import value
- B. The BGP LOCAL_PREF attribute
- C. The MED attribute
- D. The route distinguisher (RD), which adds an 8-byte value to the IPv4 prefix to form a VPN IPv4 prefix(correct)
Explanation: The correct answer is D. Cisco states that the route distinguisher adds an 8-byte value to an IPv4 prefix to create a VPN IPv4 prefix, which keeps overlapping customer prefixes unique. Option A is wrong because route targets are extended communities that control which VRFs import or export routes; they do not make prefixes unique. Options B and C are path-selection attributes and do not distinguish overlapping address space.
12. An engineer is building a DMVPN Phase 3 network in which the hub summarizes routes to the spokes and spokes build direct tunnels between each other on demand. Which pair of NHRP commands is used?
- A. `ip nhrp redirect` on the hub tunnel interface and `ip nhrp shortcut` on the spoke tunnel interfaces(correct)
- B. `ip nhrp shortcut` on the hub and `ip nhrp redirect` on the spokes
- C. `ip nhrp map multicast dynamic` on the spokes and `ip nhrp nhs` on the hub
- D. `tunnel protection ipsec profile` on the hub and `ip nhrp network-id` on the spokes only
Explanation: The correct answer is A. Cisco's Phase 3 example configures `ip nhrp redirect` on the hub, which sends a redirect to the local spoke so that it issues an NHRP resolution request, and `ip nhrp shortcut` (NHRP shortcut switching) on the spokes. Option B reverses the roles. Option C is wrong because `ip nhrp map multicast dynamic` belongs on the hub and `ip nhrp nhs` identifies the hub on the spokes. Option D lists IPsec protection and NHRP enablement, which are needed in every phase but do not trigger spoke-to-spoke shortcut tunnels.
13. A DMVPN uses EIGRP over its mGRE tunnel. Each spoke learns the other spokes' LAN prefixes, but the next hop shown for them is always the hub, so all spoke-to-spoke traffic transits the hub. Which hub tunnel-interface change allows the spokes to build direct spoke-to-spoke tunnels with this EIGRP design?
- A. Enable `eigrp stub receive-only` on the hub
- B. Disable EIGRP split horizon on the tunnel interface and use `no ip next-hop-self eigrp`(correct)
- C. Increase the EIGRP variance on the spokes
- D. Configure `ip nhrp redirect` on the spokes
Explanation: The correct answer is B. Cisco's DMVPN guide states that with EIGRP the hub disables split horizon on the tunnel interface and uses `no ip next-hop-self eigrp`, which allows direct spoke-to-spoke tunnels. Split horizon is enabled by default and would otherwise stop the hub from advertising spoke routes back out the same tunnel interface. Option A is wrong because a receive-only stub would advertise nothing. Option C is wrong because variance only affects load balancing. Option D is wrong because `ip nhrp redirect` is a hub command in the Phase 3 design, not a spoke fix for next-hop handling.
14. Two directly connected LSRs must establish an LDP session across an interface that has an access control list. Which traffic must the ACL permit for LDP discovery and session establishment?
- A. TCP port 646 for hello messages and UDP port 646 for the session
- B. TCP port 179 for both discovery and the session
- C. UDP port 646 for LDP hello messages and TCP port 646 for the session connection(correct)
- D. UDP port 646 for both hello messages and the session
Explanation: The correct answer is C. RFC 5036 states that the UDP port for LDP Hello messages is 646 and the TCP port for establishing LDP session connections is 646. Option A swaps the transport protocols. Option B uses TCP 179, which is BGP, not LDP. Option D is wrong because the session itself runs over TCP.
15. A router uses a login method list of TACACS+ first and the local username database second. A user who exists in the local database enters the wrong password, and the reachable TACACS+ server rejects the login. What happens?
- A. The router tries the local database next and the user is accepted
- B. The login fails, because a rejection from the TACACS+ server stops authentication and no further methods are tried(correct)
- C. The router skips the TACACS+ result and always prefers the local database
- D. The router prompts again, forcing the user to be authenticated by the local database
Explanation: The correct answer is B. Cisco states that the next authentication method is used only if the previous method returns an error (the server did not respond), not if it fails, and that a denial stops the process so no other methods are attempted. Options A, C and D all assume the local database is consulted after a rejection, which only happens when the TACACS+ server does not respond.
16. An extended ACL applied inbound has two entries in this order: line 10 `permit ip 10.1.0.0 0.0.255.255 any` and line 20 `deny tcp host 10.1.1.5 any eq 23`. How is a Telnet packet from 10.1.1.5 handled?
- A. It is denied, because the more specific deny entry always wins
- B. It is denied by the implicit deny at the end of the list
- C. It is denied, because TCP entries are processed before IP entries
- D. It is permitted by line 10, because processing stops at the first matching entry(correct)
Explanation: The correct answer is D. Cisco states that after a match is found no more criteria statements are checked, so entry order determines the result. The packet from 10.1.1.5 matches line 10 first. Option A is wrong because ACLs do not give priority to specificity. Option B is wrong because the implicit deny is only reached when no entry matches. Option C is wrong because entries are evaluated in list order, not by protocol.
17. An administrator applies an outbound extended ACL on the WAN interface that denies TCP port 23. The administrator then opens a Telnet session from the router's own CLI to a remote host through that interface. What is the result?
- A. The session is not blocked, because an access list does not filter traffic originating at the device itself(correct)
- B. The session is blocked, because the outbound ACL checks all packets leaving the interface
- C. The session is blocked only if the ACL is also applied inbound
- D. The session is blocked only when the ACL is a standard ACL
Explanation: The correct answer is A. Cisco states that an access list can control traffic arriving at a device or leaving a device, but not traffic originating at the device. Locally generated packets therefore bypass an outbound interface ACL. Options B, C and D are wrong because none of them changes the fact that router-originated traffic is not filtered by the ACL; filtering such traffic would require other controls.
18. On an edge interface, a packet arrives with a source address for which the FIB has a route, but that route points out a different interface than the one the packet arrived on. Which uRPF behavior is described correctly?
- A. Strict mode forwards the packet because a route exists
- B. Loose mode drops the packet because the route points to another interface
- C. Strict mode drops the packet, while loose mode forwards it because a route to the source exists(correct)
- D. Both strict and loose mode drop the packet
Explanation: The correct answer is C. RFC 3704 describes strict RPF as passing a packet only if it arrives on the interface that would be used to forward traffic back to the source, while loose RPF checks only for the existence of a route and not where it points. Here a route exists but points elsewhere, so strict mode drops and loose mode forwards. Options A and B reverse the modes, and option D is wrong because loose mode does not check the interface.
19. A user connects an unauthorized laptop that sends IPv6 router advertisements on an access port, and hosts begin using it as their default router. Which first-hop security feature, applied to the access port in the ingress direction with the device role set to host, blocks these messages?
- A. DHCPv6 Guard with the device role set to client
- B. IPv6 RA Guard with `device-role host`(correct)
- C. IPv6 Source Guard with a prefix guard policy
- D. IPv6 snooping with an empty binding table
Explanation: The correct answer is B. Cisco states that RA Guard filters RAs sent by unauthorized devices, is configured in the ingress direction on a switch port, and in host mode all RA and router redirect messages are disallowed on the port. Option A is wrong because DHCPv6 Guard blocks rogue DHCPv6 server replies and advertisements, not router advertisements. Option C is wrong because Source Guard denies traffic from addresses not in the binding table. Option D is wrong because snooping builds the binding table of neighbors; it does not by itself block RAs.
20. A network team wants a notification mechanism where the device is told that the management station received each message, and can resend it if no acknowledgement arrives. Which SNMP notification type should they configure?
- A. Informs(correct)
- B. Traps
- C. Polling with `snmp-server community`
- D. Syslog at severity 6
Explanation: The correct answer is A. Cisco states that informs require the manager to acknowledge receipt, so the agent can resend if no response arrives, whereas traps are less reliable because the receiver does not send an acknowledgement. Option B is wrong for that reason. Option C is wrong because a community string controls access to the agent and is not a notification type. Option D is wrong because syslog is a separate logging mechanism and not an SNMP notification.
21. Which TWO SNMPv3 security levels provide message authentication?
- A. noAuthNoPriv
- B. authNoPriv(correct)
- C. authPriv(correct)
- D. A read-only community string
- E. A read-write community string
Explanation: The correct answers are B and C. Cisco describes authNoPriv as MD5 or SHA authentication without encryption, and authPriv as authentication plus encryption. Option A is wrong because noAuthNoPriv matches only the username. Options D and E are wrong because community strings belong to SNMPv1 and SNMPv2c, which use a community-based form of security and act like a password rather than providing authenticated messages.
22. A router has only `logging host 10.20.30.40` configured, and `logging trap` has not been changed. Which messages are sent to the syslog server?
- A. Only emergency (level 0) messages
- B. Debugging (level 7) messages and all lower numbers
- C. Informational (level 6) messages and numerically lower levels, but not debugging messages(correct)
- D. No messages until `logging on` is explicitly configured
Explanation: The correct answer is C. The Cisco IOS XE system message logging guide states that by default syslog servers receive informational messages and numerically lower levels, so severity 7 debugging messages are not sent. Option A is wrong because the default is far broader than level 0. Option B describes the default for the console, not for the syslog server. Option D is wrong because the default settings already send informational and lower-numbered messages to a configured syslog server.
23. Clients in VLAN 10 sit behind router R1, and the DHCP server is on a different subnet. The clients' DHCP broadcasts never reach the server. Where should `ip helper-address` be configured?
- A. On the interface of the DHCP server, pointing to the client subnet
- B. Globally, with no interface context
- C. On the router interface facing the DHCP server, pointing to the clients
- D. On the client-facing router interface (the VLAN 10 gateway), pointing to the DHCP server address(correct)
Explanation: The correct answer is D. Cisco states that the relay agent is active on an interface only when `ip helper-address` is configured on it, and that interface then forwards the broadcasts it receives to the server; the relay sets the giaddr field so the server can pick the correct subnet. The broadcasts arrive on the client-facing interface. Options A and C configure the wrong interface, and option B is wrong because the command is an interface command.
24. An engineer needs per-direction jitter and packet loss measurements between two Cisco routers. Which statement is correct?
- A. Use an ICMP echo operation, because it reports one-way jitter
- B. Use a UDP jitter operation, and the IP SLAs Responder must run on the destination device(correct)
- C. Use a UDP jitter operation with no responder, because jitter is calculated by the source alone
- D. Use an ICMP echo operation with the responder, because ICMP echo needs the responder for accuracy
Explanation: The correct answer is B. Cisco states that the UDP jitter operation measures round-trip delay, one-way delay, one-way jitter and packet loss, and that the IP SLAs Responder must be running on the target device before the operation is configured. Option A is wrong because the ICMP echo operation measures end-to-end response time. Option C is wrong because the responder is required. Option D is wrong because Cisco states there is no need to configure a responder for ICMP echo.
25. In Cisco Catalyst Center (formerly DNA Center) Assurance, a router shows System Health 10, Data Plane Connectivity 9 and Control Plane Connectivity 3. What is the device health score and its category?
- A. 3, which falls in the Poor range of 1 to 3(correct)
- B. 7, which falls in the Fair range
- C. 9, which falls in the Good range of 8 to 10
- D. 0, because the device has No Health data
Explanation: The correct answer is A. The Assurance guide states that Device Health Score = MIN(System Health, Data Plane Connectivity, Control Plane Connectivity), so the lowest subscore (3) is the score, and 1 to 3 is the Poor range. Option B is an average-like value and is not how the score is calculated. Option C picks the highest subscore, which is wrong because the minimum is used. Option D is wrong because a score of 0 is used for devices without health data, such as third-party devices or devices in maintenance mode.