Skip to main content
Practice set 1 is free for every certification. Unlock sets 2-5 for $10.
Practice Exam

300-815 CLACC — Cisco Certified Specialist - Collaboration Call Control & Mobility Implementation

Test your knowledge with official exam-style questions

Questions25PassingPass/Fail (scaled score not published)Exam time90 min

Questions and options are shuffled each attempt

Email me this practice set

Get a link sent to your inbox so you can pick this back up anytime.

▶Cisco Certified Specialist - Collaboration Call Control & Mobility Implementation — Practice Set 1: All Questions & Explanations

Full question text, answer options, and explanations for this practice set — a spoiler-free alternative is the interactive quiz above for scored, shuffled practice.

  1. 1. A Cisco Unified Border Element (CUBE) with default SIP settings receives a 180 Ringing response from the service provider that carries an SDP body. How does CUBE treat this response?

    • A. Plays local ringback and ignores the SDP body
    • B. Treats it like a 183 Session Progress with SDP and provides early media cut-through(correct)
    • C. Rejects the response because ringing responses must not carry SDP
    • D. Waits for the 200 OK before it negotiates any media

    Explanation: In the Enhanced 180 Provisional Response Handling feature, the early media cut-through behavior is enabled by default, so a 180 response with SDP is treated like a 183 response with SDP and CUBE provides early media cut-through. Local ringback for a 180 with SDP only happens after early media is disabled with disable-early-media 180 under sip-ua, and a 180 without SDP always gets local ringback. Option A describes the disabled state. Option C is not described anywhere in the feature; the table lists only early media cut-through or local ringback. Option D matches the debug output seen after disable-early-media 180 is configured, where negotiation is expected in the 200 OK, so it is not the default.

  2. 2. A voice engineer wants CUBE to process an early-dialog UPDATE that carries SDP between two SIP legs. Which TWO conditions must be true according to the CUBE documentation?

    • A. Both SIP endpoints support the PRACK and UPDATE methods(correct)
    • B. The initial offer and answer were completed using reliable provisional responses(correct)
    • C. The call is a SIP-to-H.323 call so that CUBE can interwork the media change
    • D. The SDP in the UPDATE message identifies the media address with an FQDN
    • E. The UPDATE message carries a Contact header with the new endpoint address

    Explanation: The SIP UPDATE Message per RFC 3311 feature lists these prerequisites: for an early-dialog UPDATE, both SIP endpoints must support PRACK and UPDATE, and the initial offer-answer must be completed with reliable provisional responses. CUBE also rejects an early-dialog UPDATE with SDP when the peer SIP leg does not support UPDATE. Options C, D and E are listed as restrictions: UPDATE with SDP is not supported for SIP-to-H.323 calls, UPDATE with SDP that uses an FQDN is not supported, and contact information in the UPDATE message is not supported.

  3. 3. A CUBE receives a SIP INVITE and must pick an inbound dial peer. Which sequence lists the SIP inbound dial-peer match criteria in the order the documentation says they are evaluated?

    • A. incoming called-number, answer-address, then incoming uri (via, request, to, from)
    • B. answer-address, incoming called-number, then incoming uri (from, to, request, via)
    • C. incoming uri via, request, to and from, then incoming called-number, then answer-address(correct)
    • D. destination-pattern, then incoming called-number, then incoming uri via

    Explanation: The Configure Dial Peers chapter gives the order for matching inbound dial peers for SIP call legs: voice class uri with incoming uri via, then request, then to, then from, then incoming called-number (DNIS), and finally answer-address (ANI). URI-based criteria are therefore tried before the called number. Options A and B put the called-number or ANI match first, and option D starts with destination-pattern, which is not in the inbound order list.

  4. 4. An enterprise reaches its carrier through a chain of SIP proxies and wants CUBE to apply a different policy per neighboring SIP entity by using the incoming uri via command on inbound dial peers. Which entry in the SIP message does the Via-based match use?

    • A. The bottom-most Via header, which identifies the originator of the request
    • B. The From header only, because Via headers are rewritten at every hop
    • C. The top-most Via header, which represents the last hop that forwarded the request(correct)
    • D. The P-Asserted-Identity header added by the first proxy

    Explanation: The inbound dial peer matching by URI feature matches the last hop that forwarded the request, which is the neighboring SIP entity and is represented by the top-most Via header. The bottom-most Via header represents the originator of the request, so option A is the wrong end of the stack. Option B and option D are not what the incoming uri via command evaluates. The documentation also notes that URI pattern matches have no match length, so they are the least preferred when several inbound dial peers match.

  5. 5. A CUBE has one inbound dial peer that should try up to a dozen outbound SIP dial peers in a fixed preference order using a dial-peer group (destination dpg). Which statement about this feature is correct?

    • A. A dial-peer group can hold up to 100 outbound dial peers, and normal outbound dial-peer matching still runs first
    • B. If every dial peer in an active group is unavailable, CUBE falls back to the regular dial-peer search
    • C. The outbound dial peers need no destination-pattern because the group makes the match
    • D. Up to 20 outbound SIP dial peers can be grouped, and once the inbound dial peer matches no other outbound dial-peer provisioning is used(correct)

    Explanation: The feature groups up to 20 outbound SIP dial peers into a dial-peer group and sets it as the destination of an inbound dial peer. Once the inbound dial peer with an active destination group matches, dial peers from that group route the call and no other outbound dial-peer provisioning is used; a preference per member sets the selection order. Option A has the wrong limit and the wrong behavior. Option B is wrong because if all dial peers in an active group are unavailable the call is disconnected; the regular search happens only when the group itself is in the shutdown state. Option C is wrong because the destination-pattern command is still required on the outbound dial peer even though it is not used for matching.

  6. 6. A third-party SIP trunk provider sends DTMF using RTP payload types 96 and 97, but CUBE uses those same payload types for fax by default. Which action does the DTMF Relay chapter recommend?

    • A. Change the fax payload type with rtp payload-type on both the incoming and outgoing dial peers, or use asymmetric payload dtmf(correct)
    • B. Switch both dial peers to dtmf-relay cisco-rtp so that DTMF uses payload type 121
    • C. Do nothing, because Cisco devices reserve payload types 96 and 97 for DTMF
    • D. Disable dtmf-relay on the dial peers and rely on G.711 audio tones only

    Explanation: The chapter states that payload types 96 and 97 are used for fax by default on Cisco devices and that a third-party device may use them for DTMF. It recommends either changing the fax payload type on both incoming and outgoing dial peers with the rtp payload-type command or using the asymmetric payload dtmf command. Option B is wrong because cisco-rtp, with payload type 121, is not supported by CUCM and has been discontinued. Option C reverses the default use of those payload types. Option D abandons relay altogether; in-band G.711 audio is only reliable on uncompressed codecs and is not the recommended fix for a payload type collision.

  7. 7. A CUBE administrator creates a SIP profile with a rule that modifies the From header of an INVITE message. Which statement about how that rule is applied is correct?

    • A. The rule applies only to the first INVITE of a call; the REINVITE keyword is used to manipulate later INVITEs(correct)
    • B. The rule applies to every INVITE of the call, including re-INVITEs, without extra keywords
    • C. An outbound profile runs before the destination dial peer is matched
    • D. The rule can also delete the To header, because any header can be removed

    Explanation: The SIP Profiles chapter says that rules configured for an INVITE message apply only to the first INVITE of a call, and that a special REINVITE keyword is used to manipulate subsequent INVITEs. Option B contradicts this. Option C is wrong because outbound SIP profile manipulation is the last step before the message leaves CUBE, after destination dial-peer matching has taken place. Option D is wrong because removal or addition of mandatory headers (To, From, Via, CSeq, Call-Id and Max-Forwards) is not supported; they can only be modified.

  8. 8. A branch office with 300 SCCP phones needs call handling and secure voice during a WAN outage. A designer proposes using Cisco Unified CME in SRST fallback mode instead of Cisco Unified SRST to avoid extra licensing. What does the SRST Fallback Mode chapter say?

    • A. It is fine, because CME in SRST mode supports any number of phones up to the router limit and secure voice fallback
    • B. It is fine, but only if the phones use SIP, because SRST fallback mode is for SIP phones only
    • C. Unified SRST should be used, because more than 240 phones and secure voice fallback are not supported with SRST fallback using Unified CME(correct)
    • D. Unified CME must be installed with the call-manager-fallback command, because that is how CME is enabled for SRST mode

    Explanation: The chapter lists the capabilities that are not supported with SRST fallback using Unified CME and for which customers should continue to use Unified SRST: more than 240 phones during fallback service, Cisco VG 248 analog phone gateway support, secure voice fallback, and simple one-time configuration. Option A ignores those limits. Option B is wrong because SRST fallback mode is applicable only to SCCP phones and SIP phones are not supported. Option D is wrong because the call-manager-fallback command is the Unified SRST command and cannot be used on a router configured for Unified CME.

  9. 9. CUBE connects an enterprise call-control cluster to an Internet telephony service provider, which is an untrusted network. Which media path mode does the Media Path chapter recommend for this connection?

    • A. Media flow-around, because it is recommended for untrusted networks
    • B. Media flow-through, because media and signaling terminate and originate on CUBE(correct)
    • C. Media anti-tromboning, because it keeps media off the WAN
    • D. SDP pass-through in flow-around mode, because CUBE must not handle media

    Explanation: Media flow-through means that media and signaling packets terminate and originate on CUBE, which makes CUBE an active participant of the call; the chapter recommends it when connecting outside the enterprise to untrusted endpoints. Flow-around, where signaling goes through CUBE but media flows directly between endpoints, is recommended inside the enterprise with trusted endpoints, so option A is reversed. Option C is not a path mode; anti-tromboning detects and avoids loops that are created by call transfers or forwards. Option D describes pass-through with no media handling, which is not what the chapter recommends for untrusted networks.

  10. 10. A team plans LTI-based transcoding on CUBE. Which TWO statements about this feature are correct according to the Transcoding Configuration chapter?

    • A. Only a DSPFARM profile configuration is needed, and no SCCP configuration is required(correct)
    • B. The transcoding resources (DSPFARM) and CUBE must be on the same platform(correct)
    • C. Video transcoding is supported when the router has PVDM4 modules
    • D. Transcoding can be used for SRTP-passthrough calls
    • E. The DSPs perform the SRTP encryption and decryption of the media

    Explanation: LTI-based transcoding uses an internal API to reach the DSP resources, so only a DSPFARM profile (associated with the CUBE application) is required, there is no SCCP configuration, no TCP socket is opened, and the DSPFARM and CUBE must be on the same platform. Option C is wrong because video transcoding is not supported. Option D is wrong because transcoding cannot be used for SRTP-passthrough calls or when pass-thru content SDP is enabled. Option E is wrong because DSPs are not used for encryption with IOS XE; media is encrypted or decrypted as it leaves or enters the platform, which lets transcoding work for RTP-RTP, RTP-SRTP or SRTP-SRTP calls.

  11. 11. In Unified CM, a user dials a number that matches a translation pattern. What happens next?

    • A. The call is routed straight to the gateway that the translation pattern points to
    • B. Unified CM performs the digit translation and then routes the call again, using the calling search space configured within the translation pattern(correct)
    • C. Unified CM keeps using the caller's own calling search space and only changes the calling party number
    • D. The call is rejected unless a route filter is attached to the pattern

    Explanation: When dialed digits match a translation pattern, Unified CM does not send the call to an outside entity such as a gateway. It performs the translation first and then routes the call again using the calling search space that is configured within the translation pattern. Option A skips the second routing pass. Option C ignores that the translation pattern carries its own calling search space. Option D is wrong because route filters apply only to patterns that contain the @ wildcard.

  12. 12. A company with sites in many cities wants one national set of route patterns, while each call still leaves through the PSTN gateway that is local to the calling phone. Which Unified CM feature meets this requirement?

    • A. Route filters attached to every route pattern
    • B. Automated Alternate Routing groups
    • C. A time schedule on each PSTN partition
    • D. Local route groups associated with device pools(correct)

    Explanation: Local route groups decouple the location of a PSTN gateway from the route patterns used to reach it. The local route group is associated with each device pool, so phones from different locations share one set of route patterns while Unified CM selects the gateway from the device pool of the originating device. The chapter notes that this approach works for centralized call-deployment scenarios. Route filters apply only to patterns with the @ wildcard, AAR reroutes calls over the PSTN when a call is blocked for insufficient bandwidth, and a time schedule on a partition controls when the partition can receive calls, so options A, B and C do not select a gateway per caller location.

  13. 13. An administrator sets Authorization Level 100 on the international route pattern and enables Require Forced Authorization Code. Which user can complete an international call?

    • A. A user who enters a valid FAC whose authorization level is 50
    • B. A user who enters a valid FAC whose authorization level is 99
    • C. A user who enters a valid FAC whose authorization level is 100(correct)
    • D. Any user who enters a valid FAC, because the level only matters for client matter codes

    Explanation: To route the call successfully, the user's authorization level must be equal to or greater than the authorization level specified for the route pattern. A level of 100 meets a pattern level of 100, whereas 50 and 99 are lower. Option D is wrong because the authorization level is a Forced Authorization Code property (a value from 0 to 255), not a client matter code property, and it is checked against the route pattern.

  14. 14. An administrator creates a SIP trunk in Unified CM but does not select a SIP trunk security profile. What does Unified CM do?

    • A. It refuses to save the trunk
    • B. It assigns a nonsecure profile by default(correct)
    • C. It assigns an encrypted profile that uses TLS on port 5061
    • D. It inherits the profile of the device pool

    Explanation: The Configure Trunks chapter states that if you do not assign a SIP trunk security profile to your SIP trunks, Unified CM assigns a nonsecure profile by default. TLS signaling encryption requires a profile with Device Security Mode set to Encrypted and TLS as the incoming and outgoing transport type (the incoming TLS port defaults to 5061), which an administrator must create and assign. Options A, C and D describe behavior that the chapter does not state.

  15. 15. A call-center agent line is configured with Recording Media Source set to Gateway. The call is secure (SRTP) and a gateway is in the call path. Which media source does Unified CM select for network-based recording?

    • A. The gateway, because the preferred source is always honored when a gateway is in the path
    • B. The last gateway in the call path
    • C. A CUBE media proxy, because secure calls are always forked by CUBE
    • D. The phone, because for secure media Unified CM selects the phone even when the gateway is preferred(correct)

    Explanation: The recording media source selection table shows that with Gateway as the preferred source, unsecure RTP media with a gateway in the call path selects the gateway, but secure SRTP media selects the phone whether or not a gateway is in the path. Using the phone as the source requires the Built in Bridge to be enabled for that phone, either through the cluster default or on the phone itself. Option A ignores the secure-media rule. Option B applies only to the alternate source order when the first choice is unavailable. Option C is wrong because a CUBE media proxy is used for multi-fork recording to several recorders, not to select the source.

  16. 16. Which TWO statements about SIP normalization and transparency in Unified CM are correct?

    • A. A script can be applied to a SIP trunk, or to SIP lines through the SIP profile that the lines use(correct)
    • B. Default scripts cannot be edited, but you can create or import your own script(correct)
    • C. Default scripts can be edited in place when a vendor needs a small change
    • D. Transparency works when one call leg is SIP and the other is H.323
    • E. Scripts are written in XML and uploaded to the TFTP server

    Explanation: SIP normalization and transparency apply a customized LUA script to a SIP trunk (in the Trunk Configuration window) or, for SIP lines, to the SIP profile associated with those lines. Unified CM ships default scripts that you can assign but cannot edit, and you can create your own scripts or import one. Option C is wrong because the default scripts cannot be edited (copy the contents into a new script instead). Option D is wrong because for transparency to work both call legs must be SIP. Option E is wrong because the scripts are LUA scripts managed in the SIP Normalization Script window.

  17. 17. What does the Unified CM Security Guide recommend for Manufacture Installed Certificates (MICs) on Cisco IP phones?

    • A. Use MICs for the TLS connection to Unified CM, because they are signed by Cisco Manufacturing CA
    • B. Use MICs only to authenticate to CAPF for LSC installation, and use LSCs for TLS to Unified CM(correct)
    • C. Delete all MICs from the phones before any LSC is installed
    • D. Use MICs for media encryption because LSCs are used only for signaling

    Explanation: MICs are signed by the Cisco Manufacturing CA, installed automatically on supported phones, and authenticate with the Certificate Authority Proxy Function (CAPF) for Locally Significant Certificate (LSC) installation. The guide recommends using only MICs for LSC installation, because MIC root certificates are easily compromised, and upgrading phones to use LSCs for the TLS connection to Unified CM, after which the MIC root certificates should be removed from the trust store. Option A is the practice the guide advises against. Option C is wrong because MICs are used to reach CAPF, and administrators cannot modify, delete or revoke them. Option D is not described in the guide.

  18. 18. A cluster that was installed in the default security mode must now support encrypted phones. Which approach matches the Security Guide?

    • A. Run utils ctl set-cluster mixed-mode on any subscriber after installing the Cisco CTL client
    • B. Enable the CAPF and CTL services on the publisher, run utils ctl set-cluster mixed-mode on the publisher, and then check that Cluster Security Mode shows 1(correct)
    • C. Run utils sipOAuth-mode enable, which is the only way to reach mixed mode
    • D. Change Device Security Mode in the phone security profile, which switches the cluster to mixed mode

    Explanation: To move from non-secure mode to mixed mode, the CAPF and CTL services are enabled on the publisher and the CLI command utils ctl set-cluster mixed-mode is run on the publisher; the system must be registered with Smart Software Manager with export-controlled functionality allowed. The result is verified in Enterprise Parameters, Security Parameters, where Cluster Security Mode shows 1. Option A is wrong because the command runs on the publisher and the Cisco CTL client is no longer supported from Release 14. Option C is wrong because SIP OAuth mode is a separate mode for Jabber and other devices. Option D is wrong because a phone security profile applies to phones and does not change the cluster mode.

  19. 19. A user parks a call with the Park softkey at extension 8022, and nobody retrieves it. With default settings and no park monitoring, what happens when the Call Park Reversion Timer expires?

    • A. After 10 seconds the call is dropped
    • B. After 60 seconds the call is sent to voicemail
    • C. After 60 seconds the call returns to the device that parked it(correct)
    • D. After 120 seconds the call is redirected to the hunt pilot

    Explanation: The Call Park Reversion Timer default is 60 seconds; it determines how long a call remains parked, and when it expires the parked call returns to the device that parked the call (or to the hunt pilot only when a hunt group member parked a call that came through a hunt pilot). The 10-second default belongs to the Call Park Display Timer, which only controls how long the park number shows on the parking phone, so option A is wrong. Sending the call to voicemail or another number requires the optional Park Monitoring feature. Option D does not describe the standard behavior.

  20. 20. An administrator wants a hunt pilot to distribute calls to the CTI route point of an IVR application through a line group. What is the outcome?

    • A. It works, because line groups accept any directory number
    • B. It works only if the hunt pilot and the CTI route point are in different partitions
    • C. It works only after the Queue Calls option is enabled on the hunt pilot
    • D. It is not possible, because line groups cannot point to CTI ports or CTI route points(correct)

    Explanation: The Configure Hunt Pilots chapter explains that line groups point to specific extensions, typically IP phone extensions or voicemail ports, and cannot point to CTI ports or CTI route points. Hunt pilots therefore cannot be used to distribute calls to endpoints controlled by CTI applications such as an IP IVR. Partitions do not matter here, because a call distributed by a hunt pilot overrides partition and calling search space restrictions. Queue Calls adds call queuing and does not change which devices a line group may contain.

  21. 21. A traveling executive is on an active call on the desk phone and wants to continue it on a mobile phone by pressing a softkey. Which statement is correct?

    • A. Extend and Connect with a CTI remote device handles this by moving the active call to the remote destination
    • B. Unified Mobility handles this, because Move to Mobile transfers an active call from the desk phone to a configured remote destination through the Mobility softkey(correct)
    • C. Extension Mobility handles this, because the user logs the call in to the mobile phone
    • D. Neither feature is needed, because Call Park moves the call between devices

    Explanation: In Unified Mobility, Move to Mobile lets a user transfer an active call from the desk phone to a mobile device that is configured as a remote destination by pressing the Mobility softkey. The Extend and Connect chapter states that Extend and Connect does not support moving active calls between a Cisco Unified IP Phone and a remote destination, so option A is wrong. Extension Mobility only gives a user their profile on another IP phone, and Call Park holds a call so that it can be retrieved from another phone in the Unified CM system, not from a mobile phone on the cellular network.

  22. 22. In an Expressway firewall traversal deployment, which statement correctly describes the roles and the direction of the connections?

    • A. Expressway-C is the traversal server and Expressway-E is the traversal client; Expressway-E connects inward
    • B. Both systems are servers and an external client opens a connection to each of them
    • C. Expressway-E in the DMZ is the traversal server, Expressway-C is the traversal client, and all connections between them are established outbound from the client(correct)
    • D. Expressway-E is the traversal client and may only connect to a Cisco VCS acting as the server

    Explanation: The Expressway solution uses an Expressway-E on the public network or in the DMZ as the firewall traversal server and an Expressway-C (or another traversal-enabled endpoint) in the private network as the traversal client. All connections between them are outbound, established from the client to the server, so they traverse the firewall. Option A reverses the roles. Option B does not describe the solution. Option D is wrong because both the traversal client and the traversal server must be Cisco Expressway systems and neither can be a Cisco VCS.

  23. 23. Off-premises Jabber clients stop signing in through the Expressway-E after a DNS change. The team finds that the _cisco-uds._tcp SRV records can now be resolved from the public Internet. What should they do?

    • A. Keep the records public and delete the _collab-edge._tls records
    • B. Make the _cisco-uds._tcp records resolvable only on the internal network and keep _collab-edge._tls on public DNS(correct)
    • C. Move the _cisco-uds._tcp records to the Expressway-E so that they resolve to the DMZ address
    • D. Add the _cisco-uds._tcp records to the Expressway-C trust list

    Explanation: The MRA requirements say the _cisco-uds SRV records must not be resolvable outside of the internal network, otherwise the Jabber client will not start MRA negotiation via the Expressway-E. Public DNS carries the _collab-edge._tls SRV records that let endpoints discover the Expressway-E systems. Option A removes the records that MRA clients need. Option C and option D confuse DNS records with other configuration; the records are not placed on the Expressway or in a trust list.

  24. 24. An Expressway zone has its Media encryption mode set to Force encrypted. Which statement from the Zones and Neighbors chapter applies?

    • A. The zone must be configured as SIP-only, because H.323 must be disabled on a zone that uses Force encrypted(correct)
    • B. The Expressway keeps proxying the call, because only the B2BUA is invoked for Auto
    • C. The setting applies only to H.323 legs of the call
    • D. The call does not consume a Rich Media Session license, because encryption is applied in the zone

    Explanation: Any zone with an encryption mode of Force encrypted or Force unencrypted must be configured as a SIP-only zone, with H.323 disabled, and TLS transport must be enabled when Force encrypted or Best effort is required. Option B is wrong because any setting other than Auto routes the call through a B2BUA hosted on the Expressway, after which it no longer acts as a proxy. Option C is wrong because the policy is applied to the SIP leg of the call, even if other legs are H.323. Option D is wrong because the B2BUA makes the call a traversal call that uses a Rich Media Session license, except when both endpoints are registered to Cisco infrastructure.

  25. 25. An administrator adds a custom firewall rule with Transport set to UDP on an Expressway-E, activates the rule set and confirms it within the 15-second window. Test traffic still is not filtered by the new rule. What explains this?

    • A. Firewall rules apply only to traffic that arrives on the LAN 2 interface
    • B. Rules with the same priority are skipped silently until one of them is deleted
    • C. Drop actions are ignored for UDP, so the action must be changed to Reject
    • D. New UDP rules do not take effect until the next system reboot, although deleted UDP rules become inactive as soon as the rule set is activated(correct)

    Explanation: In the Configuring Firewall Rules section, new or modified rules stay pending until activated and must be confirmed within 15 seconds or they are rolled back. For custom rules with Transport set to UDP there is a special case: new UDP rules do not take effect until the next system reboot, while deleted UDP rules become inactive as soon as the rule set is activated. Option A is wrong because the Interface field matters only when the Advanced Networking option key is installed. Option B is wrong because duplicate priorities make the activation fail instead of being skipped. Option C is wrong because Drop and Reject are both valid actions; Drop simply sends no response to the sender.